Menu

Attention: Have only 1 page to see today
« previous next »
Pages: 1 2   Go Down

Author Topic: CCP25 engine arrangement  (Read 3617 times)

October 11, 2007, 01:54:54 PM
Reply #15

DOCREED

  • Information Offline
  • Posts: 369
(No subject)
« Reply #15 on: October 11, 2007, 01:54:54 PM »
Quote
Even with the bracket i'll bet a.s. left little or no access to bilges/ wiring etc. !!!(My biggest complaint about my boat).

  I can see everything but I cant touch anything.
Logged
89 250 CCP
full transom
Twin Merc 150\'s......thirsty?  YES they are.

October 11, 2007, 02:01:45 PM
Reply #16

DOCREED

  • Information Offline
  • Posts: 369
(No subject)
« Reply #16 on: October 11, 2007, 02:01:45 PM »
This is what it looks like from on board.  You really need 5' long arms to get to anything in the bilge.  If I was only a basketball player..........[  
 

][/img]
Logged
89 250 CCP
full transom
Twin Merc 150\'s......thirsty?  YES they are.

October 11, 2007, 02:31:45 PM
Reply #17

LilRichard

  • Information Offline
  • Master Rebuilder
  • Posts: 1244
(No subject)
« Reply #17 on: October 11, 2007, 02:31:45 PM »
Nice rig... I really do like the looks of that boat with a bracket.
Logged
October 17, 2007, 01:59:53 AM
Reply #18

ddd222

  • Guest
(No subject)
« Reply #18 on: October 17, 2007, 01:59:53 AM »
hey doc got trim tabs? After putting them on my boat i couldn't imagine not having them. If not i highly suggest them. I put bennett's on mine, and would prefer to recommend bennetts based on their great customer service and ultra professionalism, but regretably i think lenco tabs are better suited to smaller boats. The hydraulic pump on the bennets take up space and is a $375 part if it burns out. Mine also had a tiny chronic leak that logically went right to the bilge, but the worst part was accessing the pump. The only place i found to mount the pump was difficult to access. The leak could have been my fault when installing, but i followed the install directions to the letter. I would bet one hydraulic line got too kinked and slightly damaged in the the tight ass bilge when snaking it during install. The bennetts have an electric and hydraulic element to them. The lenco's only electric, they don't require the space needed for mounting the pump, or the cost of replacing a burnt out one
Logged
October 17, 2007, 07:17:33 AM
Reply #19

DOCREED

  • Information Offline
  • Posts: 369
(No subject)
« Reply #19 on: October 17, 2007, 07:17:33 AM »
Yes I have tabs.  They are great.  Especially with a boat with so much weight aft.  A couple of presses and the boat is level.  They come in handy when your guests dont understand trim and all hang together on one side chatting.
I have bennet tabs and they work amazingly well.  No leaks yet.

Looks like I'm going to make the trek to Tampa for the get together--hope to see you there.
Logged
89 250 CCP
full transom
Twin Merc 150\'s......thirsty?  YES they are.

October 17, 2007, 03:31:02 PM
Reply #20

gw204

  • Information Offline
  • Posts: 106
(No subject)
« Reply #20 on: October 17, 2007, 03:31:02 PM »
Forgive me if this has already been covered....

I'm wondering if you have a 20" motor when you should have a 25".  What's the model no. of your Merc?  25" will end in XL.
Logged
Brian
St. Leonard, MD
1981 Mako 17
1986 Grady White 227
February 27, 2008, 09:38:27 AM
Reply #21

DOCREED

  • Information Offline
  • Posts: 369
(No subject)
« Reply #21 on: February 27, 2008, 09:38:27 AM »
Mine are 25"
Sorry for the delay in posting but I have to check my spelling:)
Logged
89 250 CCP
full transom
Twin Merc 150\'s......thirsty?  YES they are.

Pages: 1 2   Go Up
« previous next »
 

SimplePortal 2.3.5 © 2008-2012, SimplePortal