You reached the limit of pages to see for today

Author Topic: 1986 20 ft Osprey Gas tank  (Read 2105 times)

April 10, 2006, 02:06:30 PM
Read 2105 times

bodie717

  • Information Offline
  • Posts: 5
    • http://www.albums-online.com
1986 20 ft Osprey Gas tank
« on: April 10, 2006, 02:06:30 PM »
1986 20 ft  Osprey

I found a pinhole leak under my gas tank. Should I have it repaired or get  a new tank.
All of the markings are gone from the tank, any idea what size ?
What make ?

April 11, 2006, 06:08:52 AM
Reply #1

John Jones

  • Information Offline
  • Posts: 2829
(No subject)
« Reply #1 on: April 11, 2006, 06:08:52 AM »
I assume from corrosion?  Any other corroded spots on the tank?  If so, replace it.  Gasoline leaks in an enclosed space are nothing to fool around with.

You probably aren't going to find an exact replacement.  Tons of custom tank fabricators can be found on the web.
Politics have no relation to morals.
Niccolo Machiavelli

April 11, 2006, 08:26:18 AM
Reply #2

JimCt

  • Information Offline
  • Posts: 1848
(No subject)
« Reply #2 on: April 11, 2006, 08:26:18 AM »
No question, replace it.  Measure H", W", & D" and a tank fabricator will quote you.
JimCT
------
\'74 22-2 inboard
HIN:ASPL0953M74J
Chrysler 318
------
\'74 Marshall 22

April 25, 2006, 04:40:11 PM
Reply #3

bodie717

  • Information Offline
  • Posts: 5
    • http://www.albums-online.com
(No subject)
« Reply #3 on: April 25, 2006, 04:40:11 PM »
Had tank fixed.
Tank - renue
Works like new, cut out bad spot, welded in new.
Outer coating rubberized.
Cost $350.

April 25, 2006, 08:55:20 PM
Reply #4

northguy

  • Information Offline
  • Posts: 4
gas tank
« Reply #4 on: April 25, 2006, 08:55:20 PM »
I JUST GOT DONE PULLING THE TANK ON MY 1973 179AS  I don't see any terrible corrosion but it was full of water. The boat has sat outside for awhile and the sending unit was loose.  What is th erubber products to use on the outside? Also do you think I can pressure test it for leaks? :wink:

April 26, 2006, 10:33:04 AM
Reply #5

bodie717

  • Information Offline
  • Posts: 5
    • http://www.albums-online.com
(No subject)
« Reply #5 on: April 26, 2006, 10:33:04 AM »
Check out http://www.gastankrenu.com/

Find a local dealer have it done.
I have no idea what they use, but it is baked on inside & out.
Looks new, rubber coating will keep aluminum from rusting.
Hope this helps.
Good luck

July 23, 2006, 09:24:37 PM
Reply #6

carr

  • Information Offline
  • Posts: 5
gas tank
« Reply #6 on: July 23, 2006, 09:24:37 PM »
RDS builds tanks and are coast guard approved. This is one item you don't want to skimp on.

July 23, 2006, 10:06:23 PM
Reply #7

scott_gunn

  • Information Offline
  • Posts: 186
(No subject)
« Reply #7 on: July 23, 2006, 10:06:23 PM »
I have an 87 200 Osprey and these tanks often form pinhole leaks where the neck enters the tank.  I epoxied mine.

July 24, 2006, 08:17:05 AM
Reply #8

JimCt

  • Information Offline
  • Posts: 1848
(No subject)
« Reply #8 on: July 24, 2006, 08:17:05 AM »
If the fixes work that's great... but keep a sharp eye on the tank.  A pounding hull flexes a tank continually.
JimCT
------
\'74 22-2 inboard
HIN:ASPL0953M74J
Chrysler 318
------
\'74 Marshall 22

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal