Attention: Have 2 pages to see today

Author Topic: Time for another  (Read 10151 times)

February 20, 2016, 08:19:40 PM
Reply #30

Levi

  • Information Offline
  • Posts: 143
Re: Time for another
« Reply #30 on: February 20, 2016, 08:19:40 PM »
Oh believe me Chris  a summertime run over there isn't out of the question once I get mine done but @ 5mpg I could get to Hopetown and back with 98 gallons and a light load. And the ride wouldn't be too ba d if you didn't get in a big hurry.

April 18, 2016, 08:52:48 PM
Reply #31

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #31 on: April 18, 2016, 08:52:48 PM »
Slow n steady!      Got some Tile Clad rolled in and tank put in. ~96 gal.    5200ed some 1/2x 1.5" wide strips of pvc board on the outside bottom edges and did the same on the hull side when I set it in. Four 1/4" thrubolts and some aluminum sleeves...

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Glued/glassed some 1/2 pvc board pads for mounting schtuff...

Untitled by dirtwheelsfl, on Flickr

April 18, 2016, 09:01:14 PM
Reply #32

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #32 on: April 18, 2016, 09:01:14 PM »
O forgot bulkhead pics. Just used leftover transom board and some 1" nidacore I had...

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr




April 18, 2016, 09:07:19 PM
Reply #33

CLM65

  • Information Offline
  • Posts: 1394
Re: Time for another
« Reply #33 on: April 18, 2016, 09:07:19 PM »
Nice work as usual!
Craig

2002 205 Osprey, 200 HP Yamaha OX66


1967 22-2 Flatback (Rebuild in progress)

April 19, 2016, 05:08:25 AM
Reply #34

RickK

  • *****
  • Information Offline
  • Administrator
  • Posts: 11066
Re: Time for another
« Reply #34 on: April 19, 2016, 05:08:25 AM »
Very nice Chris  :thumleft:
Rick
1971 "170" with 115 Johnson (It's usable but not 100% finished)

1992 230 Explorer with 250 Yamaha

April 28, 2016, 07:49:47 PM
Reply #35

Fletch170

  • Information Offline
  • Master Rebuilder
  • Posts: 630
Re: Time for another
« Reply #35 on: April 28, 2016, 07:49:47 PM »
Makes me feel bad about my abilities, but awesome stuff man!
1981 2100 CC Hydra Sport
1976 170 (sold)

August 03, 2016, 08:58:13 PM
Reply #36

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #36 on: August 03, 2016, 08:58:13 PM »
So the plan we came up with for this one is to lay it out like mine, front bulkhead/coffin, but with 7 hatches in the floor. 4 on the outside of console, one under leaning post, one for bilge and one large insulated one in the bow. Thought it was gonna be some full height bulkheads and casting platform but plans change...

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

These stringers created a drainage problem versus the bulkheads that I thought were going in so made some ramps/limber holes. (glass triangles and some 2 part foam)

Untitled by dirtwheelsfl, on Flickr

Foam got bedded with some sandbags

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

I don't like small drains... 1.5"

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

1708 and 10oz finish cloth

Untitled by dirtwheelsfl, on Flickr

1" Plascore layed up on one side. Waiting on some hatch rings and console to figure out the other side. It will have half round gutters ran the length connecting all the hatches underneath to drain all of them. That will run to a channel going across the transom then out the scuppers, which im not sure how theyre gonna go yet...   If that makes sense haha.

Untitled by dirtwheelsfl, on Flickr

October 02, 2016, 01:55:00 PM
Reply #37

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #37 on: October 02, 2016, 01:55:00 PM »
Pickin away at her!

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

1.5" of crown

Untitled by dirtwheelsfl, on Flickr

Buddy at L&H made the hatches n gutters

Untitled by dirtwheelsfl, on Flickr

This one is getting a new CCP coffin too

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickrv

Untitled by dirtwheelsfl, on Flickr

Andros console. Biggest hunk of :*: that will be on the boat. Theres not a flat surface on this thing anywhere!    Some of the panels are dipped 3/16"!      I said WTF is up with this thing, scratch n dent ? did you glue the coring in really hot and it shrank or what.   They claim the mold isnt fair so when they slide the tower over it the mounting pads dont scratch it, then the thrubolts pull it back out flat. Gimme a fukn break!    Hopefully theres enough meat in the compass flat on top to fair it out so it doesnt pool water. Assclowns!

O thanks again to Kevin for meeting me in Okeechobee with it!

Untitled by dirtwheelsfl, on Flickr

October 02, 2016, 07:25:48 PM
Reply #38

RickK

  • *****
  • Information Offline
  • Administrator
  • Posts: 11066
Re: Time for another
« Reply #38 on: October 02, 2016, 07:25:48 PM »
Lots of progress.  :8):  Won't be long until it starts cooling down  :49:
Rick
1971 "170" with 115 Johnson (It's usable but not 100% finished)

1992 230 Explorer with 250 Yamaha

October 03, 2016, 12:18:47 AM
Reply #39

Damage7

  • Information Offline
  • Posts: 57
Re: Time for another
« Reply #39 on: October 03, 2016, 12:18:47 AM »
Looks sweet! What's the purpose of the drain being made that way?

October 03, 2016, 08:55:41 PM
Reply #40

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #40 on: October 03, 2016, 08:55:41 PM »
Looks sweet! What's the purpose of the drain being made that way?

So the garboard drain screws are tapping into an epoxy slug versus the foam transom core. Thousands of boats are perfectly fine just tapping into the foam core and outside skin of glass but i just like doing it this way, especially with a wood core...

October 04, 2016, 02:34:15 PM
Reply #41

Levi

  • Information Offline
  • Posts: 143
Re: Time for another
« Reply #41 on: October 04, 2016, 02:34:15 PM »
 :awife: nice man looking good!

October 04, 2016, 07:28:33 PM
Reply #42

HawgLeg

  • Information Offline
  • Posts: 160
Re: Time for another
« Reply #42 on: October 04, 2016, 07:28:33 PM »
Nice work DW! Console sounds like the kind of work I got from Hammerhead on the live well. It works though...
1970 Aquasport 22-2 Flatback with Yamaha F200

November 16, 2016, 08:25:13 PM
Reply #43

dirtwheelsfl

  • Information Offline
  • Master Rebuilder
  • Posts: 808
Re: Time for another
« Reply #43 on: November 16, 2016, 08:25:13 PM »
Getting all the ducks in a row to glue this thing down!

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

These will be fun to glass on the inside.

Untitled by dirtwheelsfl, on Flickr

Girls always look better witha lil white in their belly!

Untitled by dirtwheelsfl, on Flickr

This will be a trough for drainage

Untitled by dirtwheelsfl, on Flickr

Glued this lil strip on to match the rubrail flat

Untitled by dirtwheelsfl, on Flickr

Untitled by dirtwheelsfl, on Flickr

November 17, 2016, 05:00:38 AM
Reply #44

RickK

  • *****
  • Information Offline
  • Administrator
  • Posts: 11066
Re: Time for another
« Reply #44 on: November 17, 2016, 05:00:38 AM »
Look at you, getting all fancy on the gutter drains - sweet


Looks great. How deep is the drain trough going to be?
Rick
1971 "170" with 115 Johnson (It's usable but not 100% finished)

1992 230 Explorer with 250 Yamaha

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal